Activity of reducing steel slag of EAF

Reducing steel slag (RSS) was mainly acquired from five electric-arc furnace (EAF) steelmaking plants (among them, the products of two plants were carbon steel and those of other plants were stainless steel) for research tests. The chemical properties, compound compositions, activities and contents of main expansive compounds were tested. The results showed that the field sampled RSS had a very high crystallinity and hydraulicity with main chemical compositions close to those of Portland cement. It can be known from the study that in case of C/S ratio higher than 2.0, the main compound compositions are C₂S, C₃S, C₂F and f-CaO. However, after the RSS was stored for six months, an obvious variation occurred with potential pre-hydration in RSS, where the SO₃ content was slightly reduced and the compressive activity index was obviously higher than that at the 28th day.     

Abnormal Grain Growth of Pb(Mg1/3Nb2/3)O3-35 mol% PbTiO3 Ceramics Induced by the Penetration Twin

Pb(Mg_1/3Nb_2/3)O₃-35 mol% PbTiO₃ (PMN-35PT) specimens with a 5 mol% excess PbO were prepared by excessive heat treatment at 1150°C to induce abnormal grain growth. Through electron backscatter diffraction analysis and the observation of a three-dimensional morphology, the abnormally grown PMN-35PT grains were found to be twinned crystals with penetration characteristics. The morphology of the PMN-35PT twinned crystal was crystallographically analyzed. The abnormal grain growth of PMN-35PT is suggested to be due to preferential growth at the reentrant angles formed by twins.     

Separation of humic acid with nanofiltration polyamide composite membranes

Humic acid, a natural organic matter, was separated with a polyamide (PA) composite membrane with a molecular weight cutoff (MWCO) of 500 g/mol. The PA composite membrane was prepared by the interfacial polymerization of piperazine and trimesoyl chloride on a polysulfone support with an MWCO of about 30,000 g/mol. The separation conditions through the membrane were varied, and factors affecting the permeation performance of the membranes, such as the concentration, pH, and storage time of the humic acid solutions, were studied. The surface chemistry of the membrane changed dynamically as a function of the operating time during the permeation tests, and the size and ζ potential of the colloid of humic acid solutions under different conditions were characterized with a ζ potentiometer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2847–2853, 2002     

A three-dimensional numerical simulation of the transport phenomena in the cathodic side of a PEMFC

A three-dimensional numerical model is developed to simulate the transport phenomena on the cathodic side of a polymer electrolyte membrane fuel cell (PEMFC) that is in contact with parallel and interdigitated gas distributors. The computational domain consists of a flow channel together with a gas diffusion layer on the cathode of a PEMFC. The effective diffusivities according to the Bruggman correlation and Darcy's law for porous media are used for the gas diffusion layer. In addition, the Tafel equation is used to describe the oxygen reduction reaction (ORR) on the catalyst layer surface. Three-dimensional transport equations for the channel flow and the gas diffusion layer are solved numerically using a finite-volume-based numerical technique. The nature of the multi-dimensional transport in the cathode side of a PEMFC is illustrated by the fluid flow, mass fraction and current density distribution. The interdigitated gas distributor gives a higher average current density on the catalyst layer surface than that with the parallel gas distributor under the same mass flow rate and cathode overpotential. Moreover, the limiting current density increased by 40% by using the interdigitated flow field design instead of the parallel one.     

Physical properties of poly(vinyl alcohol) fibers prepared from wet spinning/multi-step drawing

The preparation of poly(vinyl alcohol) (PVA) fibers by multi-step drawing was examined. The high draw ratio was attained when the drawing just before melting point was repeated. The influences of the draw ratio on mechanical and thermal properties of the fibers were studied. We utilized the wide angle x-ray diffraction (WAXD) as a medium to observe the erystallinity and the orientation of PVA fibers to study their effects on the physical properties of the fibers. With various coagulation bath concentration, both the tenacity and Young's modulus of fibers would increase as the draw ratios increased, the elongation would decrease at the same time. The tenacity was able to reach 41.0 cN/tex with the Young's modulus being 856.2 cN/tex; also, as the draw ratios increased, both crystallinity and orientation would increase. The crystallinity was about 67.2 % and the orientation was about 86.4%.     

Carbon nanotubes based on anodic aluminum oxide nano-template

The effect of reaction gas and catalyst on the growth of carbon nanotubes (CNTs) in the anodic aluminum oxide (AAO) nano-template was investigated. A mechanism of CNT growth was proposed, which involves the competitive catalytic carbon deposition between on the Co catalyst particles electrodeposited at the bottom of the pores and on the AAO template itself. Presence of H₂ in the reacting gas mixture significantly affected the morphology and the wall structure of synthesized CNTs: CNTs of high crystallinity grew out of pores with H₂ while no CNTs overgrew in the absence of H₂. CNT synthesis by CO disproportionation showed a lower growth rate and a higher degree of ordering than those grown by C₂H₂ pyrolysis. The unified mechanism of CNT growth on AAO template is also proposed.     

Preparation and barrier property of poly(ethylene terephthalate)/clay nanocomposite using clay‐supported catalyst

Poly(ethylene terephthalate) (PET)/clay nanocomposite was prepared by the direct polymerization with clay‐supported catalyst. The reaction degree of catalyst against the cation exchange capacity of clay was 8 wt %. The intercalation of PET chains into the silicate layers was revealed by X‐ray diffraction studies. SEM morphology of the nanocomposite showed a good dispersion of clay‐supported catalyst, ranging from 30 to 100 nm. The intercalated and exfoliated clay‐supported catalyst in PET matrix was also observed by TEM. The improvement of O₂ permeability for PET/clay‐supported catalyst composite films over the pure PET is approximately factors of 11.3–15.6. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4875–4879, 2006     

Dynamic deformation behavior of aluminum alloys under high strain rate compressive/tensile loading

Mechanical properties of the materials used for transportations and industrial machinery under high strain rate loading conditions such as seismic loading are required to provide appropriate safety assessment to these mechanical structures. The Split Hopkinson Pressure Bar (SHPB) technique with a special experimental apparatus can be used to obtain the material behavior under high strain rate loading conditions. In this paper, dynamic deformation behaviors of the aluminum alloys such as A12024-T4, A16061T-6 and A17075-T6 under both high strain rate compressive and tensile loading conditions are determined using the SHPB technique.     

3D Localization for Launch Vehicle Using Virtual TOA and AOA of Ground Stations

Wireless Personal Communications - Generally, a ground telemetry station for a launch vehicle (LV) includes a tracking function only; therefore, position measurements for LV depend on received...     

Tubular reactor design for the oxidative dehydrogenation of butene using computational fluid dynamics (CFD) modeling

Catalytic reactors have been essential for chemical engineering process, and different designs of reactors in multi-scales have been previously studied. Computational fluid dynamics (CFD) utilized in reactor designs have been gaining interest due to its cost-effective advantage in designing the actual reactors before its construction. In this work, butadiene synthesis via oxidative dehydrogenation (ODH) of n-butene using tubular reactor was used as a case study in the CFD model. The effects of coolant and reactor diameter were investigated in assessing the reactor performance. Based on the results of the CFD model, the conversion and selectivity were 86.5% and 59.5% respectively in a fixed bed reactor under adiabatic condition. When coolants were used in a tubular reactor, reactor temperature profiles showed that solar salt had lower temperature gradients inside the reactor than the cooling water. Furthermore, higher conversion (90.9%) and selectivity (90.5%) were observed for solar salt as compared to the cooling water (88.4% for conversion and 86.3% for selectivity). Meanwhile, reducing the reactor diameter resulted in smaller temperature gradients with higher conversion and selectivity.